Showing posts with label Spike's Tactical lower receiver. Show all posts
Showing posts with label Spike's Tactical lower receiver. Show all posts

Monday, March 28, 2016

Shoot Your Guns



Some people have ONE gun, others have several, but whatever the case, the song remains the same. If you're going to be any good with firearms you have to actually shoot them, as opposed to staring at them fondly as they stand gleaming in their racks.


Thieves

That was brought home to me a little while ago, after a dismal offhand performance against some steel plates. The expression, "couldn't spot a thieving hippy on the hustle in Austin from 10 paces" totally applied, embarrassingly. So I set out to change that, with a Glock 21, an AR 15 and a Ruger American .22.




After a brisk warm up against an unfortunate silhouette, the plates were swinging at 50 and 75 yards. Well done, Ruger. 


Here's a Handy Chart

I left the rifle zeroed at 50 yards; just dial it up a fraction under 5.5" for 100 yards. And note how the Ruger American takes the ubiquitous 10/22 30 round magazine. Good job, team.

The AR did fine, too, and made handy work of an empty value pack of .223. It has a Primary Arms 1x6 scope on it, which I'm tempted to upgrade. Perhaps with a Vortex Strike Eagle.




Then there's Glock. Some people don't like Glocks and call them "rubbish." Well, the Glock 21 isn't a Colt Python and it can't send the mighty .357 Magnum through your enemy's engine block, but still, I'm not complaining. That pistol is all business.

Shoot over, head for home.

Gun Rights,

LSP

Tuesday, August 25, 2015

Fix Your AR 15's Jammed Bolt Catch Assembly



I came to the end of a magazine of 5.56 and the bolt closed in the receiver, instead of being held open by the bolt catch. Hunh, that's weird, I thought wisely to myself, like a firearms professional, and had a look at the weapon. It turns out the catch had jammed and wouldn't rise to catch the bolt when the magazine was empty. What had gone wrong? I took bolt catch assembly apart to find out.


All Taped Up

It's not hard, tape up the receiver to stop it getting scratched, then tap out the roll pin that holds the assembly in place. Save yourself some aggro and use a roll pin punch. Pin out, remove the catch, its spring and its detent. Look at these items in wonder and inspect their various wells to check for Hillary's emails, or anything else that might have jammed the catch.

Bolt Catch Assembly. Don't Lose the Spring, or the Pin, or the Detent, or the Catch.

Inspection passed, reassemble the catch using a drift pin to hold it in place, I used a small punch, then test its movement. Notice that the catch is sticking and that it doesn't want to release when it's tapped into the receiver. Why?

Tap Out the Roll Pin

I had a closer look and saw that the face of the catch was fractionally proud to its inletting in the receiver, which produced friction and stopped the catch's movement.

Diamond Coat File and Blue Heeler

So I pulled the catch and filed the offending metal down with the diamond coat file on my Leatherman Wave. Not much, about the thickness of a piece of paper, 0.1 mm. Then I tested its movement to see if it was still jamming. It didn't, good result.

Get a Roll Pin Starter Punch, they're Helpful

Then put the spring back its hole, and the detent in the spring. Don't lose the spring and the detent by idly flinging them across your workbench, because if you do the bolt catch won't work. Next replace the catch, using a drift pin to hold it in place, and see if the thing works. It does. 

Use a Small Hole Punch as a Drift Pin

Keeping the drift pin in place, tap in the assembly's roll pin, using a roll pin starter punch to get it going, and finish off with a roll pin punch until the pin's in position. Test the assembly and note with a warm glow of inner satisfaction that the catch doesn't stick and jam anymore. Well done, hopefully the problem's solved.

To make sure, put the rifle back together again and place an empty magazine in its well. Pull back on the charger and release. Will the bolt catch move upwards thanks to the pressure of the magazine spring and hold the bolt open? Will your expert machining be vindicated? A moment of bated breath and... yes, it works.

And it Works

Congratulations, you are now a Bolt Catch Assembly Technician (BCAT).

With that in mind, I think I'd better go and range test this beast.

Gun rights,

LSP